The more I test and use pistols, the more I respect the reliability of these machines. Kimber, colt, Glock, Ruger, Smith and Wesson, SIG and CZ have very good tolerances. When we fire these pistols from the range, we should be fully confident that they will be fired again and again without any problem. After all, many of these pistols are based on service pistols, designed for terrible situations.
In 1911, for example, colt was famous for operating in mud or snow. Sigp226 stood out in a rigorous test, firing 228000 bullets in a tough plan. Again, these pistols need to be repaired. They need to be cleaned and lubricated. Many will get dirty, but not dry.
If the pistol is not cleaned properly, eccentric wear will hinder its function. Normal wear is uniform wear. The muzzle of the gun is worn, so will the pistol when it is used. The spring will eventually wear out and need to be replaced. The hole is worn. Eccentric wear is different.
The surface or parts of the pistol were gouged by foreign bodies. Dirt, grit and unburned powder can cause eccentric wear. If the tolerance is such that good accuracy is guaranteed, the pistol will not be accurate at all if the operating mechanism is full of fly ash shot. Lead accumulation is worse.
The frequently asked question is how often should we clean the pistols? The answer really depends on the weapon. The 22 caliber rimfire should be cleaned regularly. Since this caliber uses gunpowder,. 22 is the dirtiest bullet. If not cleaned, few 22 pistols can shoot more than 300 shots without failure.
A modern 9mm autoloader, which fires high-quality factory jacketed bullets, may have to fire thousands of bullets before the function becomes dull due to the accumulation of unburned gunpowder, but we really don't want to abuse our weapons. Even handguns that will perform well without cleaning in a high round count still need lubrication.
The revolver springs never seem to go wrong because they are not compressed when stored. In competitions similar to Glock, Siegel, Beretta and other high-quality autoloaders, the autoloader should have recoil springs replaced every 3000 to 5000 rounds.
We all know that pistols have not changed the springs since World War II, but that's not the best performance at all. We buy high-end pistols, so we don't have to worry about reliability, but maintenance is part of every gun.
Browning, Luger, Smith and Wesson. 22 is leisure and cleaning needs. When the cabin began to look rough and the bolts seemed to work with lubricant and fly ash grease, I cleaned MkIII. When the pistol is clean, the lubricant is applied to the function. When fly ash is present, the soup becomes turbid. When you go to the range, you lubricate the pistol harder because you can fire hundreds of bullets. It's better to carry a thin gun with you. At the end of each practice, I always take off my gun, wipe it clean and apply lubricating oil. It conducts a thorough field inspection every 500 rounds or so. When you are faced with a key event, the event is out of control and many factors are beyond your control. One thing you can control is that the pistol will be clean, ready, well lubricated, and in maximum firing conditions.
Field stripping
The owner's manual usually has good information about the field peeling pistol. Field stripping is simply to remove the slide rail from the frame of the automatic loading pistol, and then separate the barrel, spring and recoil rail from the slide rail. Revolvers usually don't need to be stripped on site at all, although you need to learn to remove proper cleaning cylinders from a single action revolver.
Professionals will learn to peel off details to properly maintain the trigger action, but fans don't have to. Most institutions have an armory for guns. If you want to modify a problem pistol, let's hope you and the director's name are based on it.
Attempting to dismantle a firearm without knowing the correct procedure can easily damage the catapult, extractor or striker. For example, it's easy to strip a series 70 1911 on site. After the striker simply slides out, the deletion of the striker stops. The Hyundai Series 80 and the striker block are another thing.
Some pistols have blind holes and other differences, which is really important. There is only one right way to do things, and that is to learn. Simple things like passing a spring through a room may not be serious, but the widget may fly and not be found.
According to experience, better quality guns are simpler. As an example, Smith and Wesson revolvers follow a template that hasn't changed for many years, except to upgrade to transfer bar ignition. The cheaper Smith and Wesson clones have small parts that are easy to lose, which are meaningless, such as the blind hole spring in the side panel, complicated disassembly. On the other hand, Luger makes the revolver simpler and more durable, and takes the SR 1911 automatic and permanently attached to the plunger tube. In this way, in this ancient design, there is a project worthy of attention. Take every pistol as a problem, and be completely familiar with the design and disassembly. There are several layers of difficulty in disassembly and disassembly.
Probably the easiest way to take and clean Beretta 92, SIG P226, and Walter P1 autoloaders. Remove the pistol, press a removal lever forward, and then move the slider forward for routine maintenance. Cz75 is a bit complicated, and 1911 was more complicated, though not difficult. The smaller the pistol, the more difficult it will be in some cases, because reducing the size of the parts will affect the design. Depending on the pistol, the difficulty of stripping in the field may be a determining factor when choosing your pistol.
When you start taking care of the pistol, make it a habit to set aside a designated work area. In some cases, the cleaning materials you use can be dangerous, although the main problem is the strong smell. The smell is more pronounced in small work areas. Well ventilated areas are important. The chemicals you are dealing with have certain properties that can cut lead and powder deposits.
It's a good idea to cover the table with a thick plastic sheet. Even garbage bags work well. A wastebasket will be used to handle your cleaning patch when you finish the housework. Cleaning is necessary and should be studied correctly.
Before you clean up, make sure the pistol is unloaded and the ammunition is not in the same room. Many of the chemicals used in the cleaning will kill the detonator of the ammunition, so the materials used to clean the pistol should be isolated from the ammunition. After unloading, check the bore of the pistol carefully. Ensure that the magazine is removed; They also need attention.
Wear goggles. When you clean the bucket hard, there will be drops of solvent into the air. Don't wipe on expensive tablecloth! Break the pistol into basic parts. If you want to clean the revolver, just open the cylinder. If you want to go a little deeper than the stripping on site, carefully remove the tray or splint before cleaning.
Some pistols have blind holes and other differences, which is very important. There is only one right way to do things, and that is to learn. Simple things, such as passing a spring through a room, may not be serious, but small parts may fly and cannot be found.
According to experience, better quality guns are simpler. As an example, Smith and Wesson revolvers follow the template and have not changed for many years, except to upgrade to transfer bar ignition. The cheaper Smith and Wesson clones have small parts that are easy to lose, which are meaningless, such as blind hole springs in the side panel, and complicated disassembly. On the other hand, Luger makes the revolver simpler and more durable, and takes the SR 1911 automatically and permanently connected to the plunger tube. In this way, in this ancient design, there is a project worthy of attention. With each pistol as a problem, fully familiar with the design and disassembly. There are several layers of difficulty in disassembly and disassembly.
Probably the easiest way to take and clean the Beretta 92, signal P226, and Walter P1 autoloader. Remove the pistol, press the lever forward, and then move the slider forward for routine maintenance. Cz75 is a bit complicated, and 1911 was more complicated, though not difficult. The smaller the pistol, the more difficult it will be in some cases, because reducing the size of the parts will affect the design. Depending on the pistol, the difficulty of undressing in the field may be the decisive factor in the choice of pistol.
When you start to keep a pistol, make it a habit to set aside a designated work area. In some cases, the cleaning materials you use can be dangerous, although the main problem is the strong smell. This odor is more pronounced in small work areas. Well ventilated areas are important. The chemicals you're dealing with have certain properties that can cut lead and powder deposits.作者: qq8500944254 时间: 2021-7-22 16:06:20